SCREEN CONFIDENTIAL
PT-R4xxx V1.10
******************** Detail message ********************
Ex101 : Nip roller does not ascend.
Ex102 : Nip roller does not descend.
Ex103 : Transport unit does not ascend.
Ex104 : Transport unit does not descend.
Ex105 : Trail clamp arm does not ascend.
Ex106 : Trail clamp arm does not descend.
Ex107 : Squeeze roller does not descend.
Ex108 : Squeeze roller does not ascend.
Ex109 : Trail clamp cannot be locked. PH24-1/2 or M24 is illegal.
Ex10a : Trail clamp cannot be unlocked. PH24-1/2 or M24 is illegal.
Ex10b : Balancer drive pin cannot be initialized.
Ex10c : The both of Home and Away side drive pin for the balancer can not be pulled out.
Ex10d : The both of Home and Away side drive pin for the balancer can not be inserted.
Ex10e : Bar for releasing the lead clamp does not ascend.
Ex10f : Bar for releasing the lead clamp does not descend.
Ex110 : Shutter does not open.
Ex111 : Shutter does not close.
Ex112 : Plate size (in the Y direction) is shorter than the set value.
Ex114 : Not bring down squeeze at loading.
Ex115 : Plate size (in the Y direction) is longer than the set value.
Ex116 : Servo status is illegal.
Ex117 : Servo status is error.
Ex118 : Servo alarm.
Ex11a : Drum speed is set beyond the permitted rate of the servo controller.
Ex11b : Current drum's encoder pulse is beyond 4000.
Ex11c : Error has occurred during drum positioning.
Ex11d : When the clamp is locked, some tail clamps are detected on the clamp arm, or when the clamp is
unlocked, some tail clamps are not detected on the clamp arm.
Ex11e : Drum's encoder pulse is beyond the permitted range after drum positioning.
Ex11f : Plate cannot be transferred into the transport unit.
Ex120 : Balancer pin cannot be detected before inserted.(Home side)
Ex121 : Balancer pin cannot be detected before pulled out (the balancer is not moving).(Home side)
Ex122 : Clamp arm and squeeze roller do not descend.
Ex123 : Trail clamp is half-locked.
Ex124 : The plate passing-sensor for unloading (PH54) does not switch to ON.
Ex125 : Time-out error has occurred when the squeeze roller ascends and clamp cam descends
simultaneously.
Ex126 : There was no plate to move to the shutter.
Ex127 : Servo controller does not enter the "Ready" status.
Ex128 : No balancer has been detected by the balancer search sensor.
Ex12c : Error has occurred on the Home side of the alignment plate (while alignment is performed).
Ex12d : Error has occurred on the alignment plate (while alignment is performed).
Ex12e : Error has occurred on the Home and Away sides of the alignment plate (when alignment is
performed).
Ex12f : Plate is not transferred to the punch unit.
Ex130 : Plate does not leave the punch unit.
Ex131 : Time-out error has occurred when Punch 1 is activated.
Ex132 : Time-out error has occurred when Punch 2 is activated.
Ex133 : Time-out error has occurred when Punch 3 is activated.
Ex134 : Time-out error has occurred when Punch 4 is activated.
Ex135 : Time-out error has occurred when Punch 5 is activated.
Ex136 : Time-out error has occurred when Punch 6 is activated.
Ex137 : Time-out error has occurred when Punch 7 is activated.
Ex138 : Time-out error has occurred when Punch 8 is activated.
Page (1)
SCREEN CONFIDENTIAL
Ex139 : After a plate is transferred to the gripper clamp, the plate detection sensor (PH29H/A) does not
switch to ON.
Ex13a : When the clamp arm is lowered, the sensor (to detect whether the clamp arm pins are hooked on the
clamp properly) has been turned ON.(Home side)
Ex13b : The specified encoder pulse for the drum is beyond 4000.
Ex13c : The transport unit's Away side is not moving during its operation.
Ex13d : The transport unit's Home side is not moving during its operation.
Ex13e : Error has occurred on the Home side of the alignment plate (while the alignment plate is finely
returning to its origin).
Ex13f : Error has occurred on the Away side of the alignment plate (while the alignment plate is finely
returning to its origin).
Ex140 : Error has occurred on the Home and Away sides of the alignment plate (while the alignment plate is
finely returning to its origin).
Ex141 : A plate remains in the transport unit when the machine received a request command.
Ex142 : A plate remains in the transport unit during error handling.
Ex143 : A plate remains on the discharge table in the transport unit.
Ex144 : A plate remains on the insertion table in the transport unit.
Ex145 : Plate cannot be moved onto the discharge table during initialization.
Ex146 : Plate cannot be moved onto the insertion table.
Ex147 : Balancer search operation has not been completed properly.
Ex148 : When the transport unit descends, only the Home side Down sensor in the transport unit is turned
ON.
Ex149 : When the transport unit descends, only the Away side Down sensor in the transport unit is turned
ON.
Ex14a : When the transport unit ascends, only the Home side UP sensor in the transport unit is turned ON.
Ex14b : When the transport unit ascends, only the Away side UP sensor in the transport unit is turned ON.
Ex14c : Front, rear or side cover is open.(Some interlock switches are OFF.)
Ex14d : A fuse on the relay board was blown. (home)
Ex14e : Thumbscrew is not tightened securely on the rear cover. (The servo stop switch is ON.)
Ex14f : A plate exists on the discharge table in the transport unit during initialization.
Ex150 : A plate exists on the insertion table in the transport unit during initialization.
Ex151 : Number of balancers is not sufficient. (The number of balancers checked with the balancer search
sensor was one, two or three for both the Home and Away sides.)
Ex152 : Clamp arm is not in the UP position.
Ex153 : A fuse on the relay board was blown. (away)
Ex154 : Blower is turned off but signal does not change.
Ex155 : Tail clamps are missing during initialization.
Ex156 : The size check program of the cetering function detects that the measured plate size is longer than
expected one.
Ex157 : The size check program of the cetering function detects that the measured plate size is shorter than
expected one.
Ex158 : Both of Home and Away size check sensors are on before starting the centering program.
Ex159 : Auto-loader is stopped by a interlock OFF.
Ex15a : This hardware matching is illegal.
Ex15b : The balancer is not moved to the target position.
Ex15c : The drum can not be spun up because the Home-Upper sensor of the Lead clamp release bar is off.
Ex15d : During the plate loading, double plate loading is detected.
Ex15e : The loaded plate is floating from the drum is detected during drum spining.
Ex15f : The drum cannot be spun up because the Upper sensor of the clamp arm is off.
Ex160 : The drum can not be spined up because the Home-Upper sensor of the clamp arm is off.
Ex161 : The drum can not be spined up because the balancing pin (Away side) is not in the waiting position.
Ex162 : The drum can not be spined up because the balancing pin (Home side) is not in the waiting position.
Ex163 : The drum can not be spined up because the Upper sensor of the squeeze roller is off.
Ex164 : The drum can not be spun up because the Away-Upper sensor of the Lead clamp release bar is off.
Ex165 : The drum is rotated to "lead clamp position", but status of Servo controller (SVC) is not changed to
"Ready".
Ex166 : The drum is rotated to "tail clamp position", but status of Servo controller (SVC) is not changed to
"Ready".
Page (2)
SCREEN CONFIDENTIAL
Ex167 : The drum is rotated to "squeeze position", but status of Servo controller (SVC) is not changed to
"Ready".
Ex168 : The drum is rotated to "balance pin before inserted", but status of Servo controller (SVC) is not
changed to "Ready".
Ex169 : The drum is rotated to "balance pin after inserted", but status of Servo controller (SVC) is not
changed to "Ready".
Ex16a : The drum is rotated to "pick up tail clamp", but status of Servo controller (SVC) is not changed to
"Ready".
Ex16b : The drum is rotated to "plate remove", but status of Servo controller (SVC) is not changed to
"Ready".
Ex16c : SVC Error has occurred during drum positioning for lead clamp.
Ex16d : SVC Error has occurred during drum positioning for tail clamp.
Ex16e : SVC Error has occurred during drum positioning for squeeze.
Ex16f : SVC Error has occurred during drum positioning for balance pin insertion.
Ex170 : SVC Error has occurred during drum positioning for balance pin pulling out.
Ex171 : SVC Error has occurred during drum positioning for picking up tail clamp.
Ex172 : SVC Error has occurred during drum positioning for plate removing.
Ex173 : Time-out error has occurred during drum positioning.(lead clamp position)
Ex174 : Time-out error has occurred during drum positioning.(tail clamp position)
Ex175 : Time-out error has occurred during drum positioning.(squeeze position)
Ex176 : Time-out error has occurred during drum positioning.(balance pin before inserted)
Ex177 : Time-out error has occurred during drum positioning.(balance pin after inserted)
Ex178 : Time-out error has occurred during drum positioning.(pick up tail clamp)
Ex179 : Time-out error has occurred during drum positioning.(plate remove)
Ex17a : After verifying the removal of the plate, press the OK button.When the OK button is pressed,
initialization begins.
Ex17b : PH62A-sensor is illegal. The sensor detects a plate during initialization.
Ex17c : PH29H-sensor is illegal. The PH29H-sensor does not turn ON during initialization.
Ex17d : PH61H-sensor is illegal. The sensor detects a plate during initialization.
Ex17e : PH61A-sensor is illegal. The sensor detects a plate during initialization.
Ex17f : PH29A-sensor is illegal. The PH29A-sensor does not turn ON during initialization.
Ex180 : Drum does not start rotating at high-speed.
Ex181 : Drum does not rotate at the specified high-speed.
Ex182 : Error has occurred after the drum rotated at the specified high-speed.
Ex183 : Drum cannot be stopped when rotating at high-speed.
Ex184 : Drum operation is halted with an emergency stop command.
Ex185 : Drum operation is stopped with a abort command.
Ex186 : Drum's vacuum pressure is not sufficient. Please confirm connection of the blower-hose, or the
Vacuum-sensor is illegal.
Ex187 : Error has occurred on the blower or the power supply of the blower is OFF.
Ex188 : Drum operation is halted due to low pressure in the drum.
Ex189 : Door is open.
Ex18a : Door does not open.
Ex18b : Transport tasks: Parameter error
Ex18c : Error has occured on the blower. Please turn off this machine, and turn on after waiting 10 seconds.
Also, confirm whether or not the connector doesn't come off.
Ex18d : The drum can not be spun up, because some of the interlock switches are OFF, or some of the
actuator's sensors are damaged, or the blower is damaged.
Ex18e : Door does not opend, because some interlock switch are OFF(front, rear or side cover is open).
Ex190 : Clamp arm does not descend.(Home side)
Ex191 : Clamp arm does not descend.(Away side)
Ex192 : Clamp arm does not ascend.(Home side)
Ex193 : Clamp arm does not ascend.(Away side)
Ex194 : When the clamp arm is lowered, the sensor (to detect whether the clamp arm pins are hooked on the
clamp properly) has been turned ON.Away side)
Ex195 : Trail clamp cannot be locked.(Home side)
Ex196 : Trail clamp cannot be locked.(Away side)
Ex197 : Trail clamp cannot be unocked.(Home side)
Page (3)
SCREEN CONFIDENTIAL
Ex198 : Trail clamp cannot be unocked.(Away side)
Ex199 : Balancer drive pin cannot be inserted.(Home side) Either of PH11-1H,PH11-2H or M11H is illegal.
Ex19a : Balancer drive pin cannot be inserted.(Away side) Either of PH11-1A,PH11-2A or M11A is illegal.
Ex19b : Balancer drive pin cannot be pulled out.(Home side) Either of PH11-1H,PH11-2H or M11H is illegal.
Ex19c : Balancer drive pin cannot be pulled out.(Away side) Either of PH11-1A,PH11-2A or M11A is illegal.
Ex19d : Balancer pin cannot be detected before inserted.(Away side)
Ex19e : Balancer pin cannot be detected before pulled out (the balancer is not moving).(Away side)
Ex19f : No balancer has been detected by the balancer search sensor.(Home side)
Ex1a0 : No balancer has been detected by the balancer search sensor.(Away side)
Ex1a1 : Number of balancers is not sufficient. (Home side)
Ex1a2 : Number of balancers is not sufficient. (Away side)
Ex1a3 : Soft-interlock or drum-stop swtich is OFF during drum spining.
Ex1a4 : The cover-interlock switch is OFF during drum spining.
Ex1a5 : The interlock switch-3 is OFF during drum spining.
Ex1a6 : A plate cannot be carried into the transport unit.
Ex1a8 : Auto-loader is not turned on, or some interlock switches on Auto-loader are OFF. Please turn on
Auto-loader, or all interlock switch.
Ex1a9 : Cassete carrier was removed. Please set cassette carrier.
Ex1aa : The door of the cassette part is open.
Ex1ab : Maintenance-cover of Auto-loader was opend. Please clode maintenance-cover.
Ex1ac : Bridge cover-2 was opened. Please clode bridge cover-2.
Ex1ad : A slipping paper under a plate was detected. Or a plate size (in the Y direction) is shorter than the set
value.
Ex1ae : A slipping paper on a plate was detected. Or a plate size (in the Y direction) is shorter than the set
value.
Ex1b0 : Trail clamp is not detected on the clamp arm before the plate loading.
Ex1b1 : Trail clamp is detected on the clamp arm before the plate unloading.
Ex1b2 : Trail clamp cannot be set correctly.
Ex1b3 : This plate can't be transed. Because something error has occured when the transfering to AT.
Ex1b4 : This plate can't be transed. Because trans path position is down.
Ex1b6 : The bridge-passing sensor does not turn OFF.(for Jig mode)
Ex1b7 : A plate remains on the plate detection sensor(PH70).
Ex1b8 : When detects the front of a plate, the detection area is not brought.
Ex1b9 : When detects the front of a plate, the detection of Home or Away is not brought.
Ex1ba : PH11-2H-sensor is illegal. The PH11-2H-sensor does not turn ON during initialization.
Ex1bb : PH11-2A-sensor is illegal. The PH11-2A-sensor does not turn ON during initialization.
Ex1c0 : Lead clamp release bar cannot be driven. Either PH30H or PH31H is illegal.
Ex1c1 : Lead clamp release bar cannot be driven. Either PH30A or PH31A is illegal.
Ex1c2 : Trans path cannot be driven. Either PH55, PH56, or PH57 is illegal.
Ex1c3 : Trans path cannot be driven. Either PH56, or, PH57 is illegal.
Ex1c4 : Trans path cannot be driven. Either PH55, or, PH56 is illegal.
Ex1c5 : Trans path cannot be driven. Either PH55, or, PH57 is illegal.
Ex1c6 : Trail clamp arm cannot be driven. Either PH20 or PH21 is illegal.
Ex1c7 : Trail clamp arm cannot be driven. Either PH20 or M20 is illegal.
Ex1c8 : An interleaf was detected under a plate.
Ex1c9 : When centering alignment is performed, the plate set position is out of range or the measured plate
size is longer than the expected one.
Ex1ca : Error has occured on the punching unit. The punch hole could not be opened correctly.
Ex1cb : Opened shutter obstructs trans path driving.
Ex1cc : Trail clamp arm obstructs trans path driving.
Ex1cd : A plate remains in a machine.
Ex1ce : When the plate is unloaded, the plate pass sensor (PH59) does not switch to ON.
Ex1d0 : Transfer operation is halted with a abort command.
Ex1d1 : Transport tasks are being processed.
Ex1d2 : Transport tasks are not being processed.
Ex1d3 : Transport tasks: Message order error
Ex1d4 : Transport system is not initialized.
Ex1d5 : Loose plate detection sensor is illegal.
Page (4)
SCREEN CONFIDENTIAL
Ex1d6 : Clamp arm sensors are illegal. (PH20,PH21)
Ex1d8 : Clamp bolt sensors are illegal. (PH24-1,PH24-2)
Ex1d9 : Transport unit position sensors are illegal. (PH55,PH56,PH57)
Ex1dc : Sampling the plate displacement detection did not end.
Ex1e0 : SVC user parameter breakdown
Ex1e1 : SVC user parameter setting error
Ex1e2 : SVC over-current
Ex1e3 : SVC detection of regenerative error
Ex1e4 : SVC postion error pulse overflow
Ex1e5 : SVC Main circuit voltage error detection
Ex1e6 : SVC overspeed
Ex1e7 : SVC overloaded (high load)
Ex1e8 : SVC overloaded (low load)
Ex1e9 : SVC stauts 99h
Ex1ea : SVC heat sink has overheated.
Ex1eb : SVC stauts b1h
Ex1ec : SVC is out of control.
Ex1ed : SVC phase error has been detected in the encoder.
Ex1ef : SVC A and B phase for the encoder has broke down.
Ex1f0 : SVC C phase for the encoder has broke down.
Ex1f1 : SVC some phases of power line is open.
Ex1f3 : SVC An instantaneous loss of power has occurred
Ex1f4 : SVC unknown error
Ex200 : Exposure operation is interrupted with a abort command.
Ex201 : Exposure processing task is now processing another message.
Ex202 : Cancellation requested while no processing is being performed.
Ex203 : PGON is not asserted.
Ex204 : START signal is not asserted.
Ex205 : START signal is not negated.
Ex206 : Test pattern; Data is not transferred.
Ex207 : Test pattern; Data transfer is not completed.
Ex208 : Reset procedure for Image board is not completed.
Ex209 : The set value for the drum rotation speed is too large.
Ex20c : Recording head has traveled beyond the limit (on the Away side).
Ex20d : Recording head has traveled beyond the limit (on the Home side).
Ex20e : Recording head positioning range error
Ex20f : Recording head has not been positioned at its origin. (origin sensor does not turn OFF.)
Ex210 : Recording head has not been positioned at its origin. (origin sensor does not turn ON.)
Ex211 : Emergency stop is requested for the secondary-scanning motor.
Ex212 : Secondary-scanning motor is deactivated with a abort command.
Ex213 : Secondary scanning motor is illegal.
Ex214 : Exposure in the secondary scanning direction exceeds the effective image output range.
Ex215 : FPGA sequence error.
Ex216 : Time-out error has occurred when the secondary scanning motor is activated.
Ex217 : EZ search has not detected the ORG sensor.
Ex218 : EZ search has not detected the EZ sensor.
Ex219 : When the CAL sensor search was executed, the maximum light intensity was less than 50 mW.
Ex21a : When the CAL sensor search was executed, the light intensity at the measurement starting point was
the maximum.
Ex21b : When the CAL sensor search was executed, the light intensity at the measurement end point was the
maximum.
Ex21c : CAL sensor search has not detected the over travel limit switch on the recording head's Home side.
Ex21d : Test pattern parameter error
Ex21e : PGON signal is not negated.
Ex21f : Secorndary direction original point setup procedure failure.(The calibrated original point is not same
as logical original point)
Ex220 : After an image data transfer from RIP is interrupted, it isn't resumed.
Ex221 : Drum rotation error was detected. This plate will be unloaded because it could not be exposed
Page (5)
SCREEN CONFIDENTIAL
correctly.
Ex222 : An error was detected in the exposure control signal. This plate will be unloaded because it could not
be exposed correctly.
Ex223 : The secondary-scanning area counter overflowed.
Ex224 : Hungup was detected.
Ex225 : An error was detected in the exposure preparation processing.
Ex300 : Both op plate pad and paper pad are not in original point.
Ex301 : After a slipping paper is removed, plate cannot be detected.
Ex302 : A slipping paper on a plate was detected. Or a plate size (in the Y direction) is shorter than the set
value.
Ex303 : Plate pad cannot be initialized.
Ex304 : Plate pad cannot carry a plate.
Ex305 : During the carring a plate, plate pad dropped the plate.
Ex306 : Paper pad cannot be initialized.
Ex307 : Air pressure in the plate pad does not go down.
Ex308 : Air pressure in the paper pad does not go down.
Ex309 : Time-out error has occurred when plate pad was moved.
Ex30a : Time-out error has occurred when paper pad was moved.
Ex30b : Time-out error has occurred when plate pad was moved intermittently.
Ex30c : Time-out error has occurred when paper pad was moved intermittently.
Ex30d : A plate cannot be carried into the transport unit.
Ex30e : During the removing a paper, PH90 does not switch to ON.
Ex30f : During the removing a paper, PH90 does not switch to OFF.
Ex310 : Maintenance cover of auto-loader is open. Please close maintenance cover.
Ex311 : Bridge cover-2 of auto-loader is open. Please close bridge cover-2.
Ex312 : Cassette carrier is not set. Please set cassette carrier.
Ex313 : A plate remains in the bridge unit.
Ex314 : A paper remains in the paper exit.
Ex315 : Nip roller does not ascend.
Ex316 : Nip roller does not descend.
Ex317 : Auto-loader is not turned on, or some interlock switches on Auto-loader are OFF. Please turn on
Auto-loader, or all interlock switch.
Ex318 : A plate cannot be carried to the bridge-passing sensor.
Ex319 : The plate pad went down from original point.
Ex31a : The paper pad went down from original point.
Ex31b : Maintenance-cover of Auto-loader was opend. Please clode maintenance-cover.
Ex31c : Bridge cover-2 was opened. Please clode bridge cover-2.
Ex31d : Door was opened. Please close the door.
Ex31e : Cassete carrier was removed. Please set cassette carrier.
Ex31f : During the carring a paper, paper pad dropped the paper.
Ex320 : Plate pad dropped a plate, until the plate pad arrived at intermediate sensor.
Ex321 : A slipping paper on front of a plate was detected.
Ex322 : A plate remains on the sensor-2 of the bridge.
Ex323 : Intermediate sensor is OFF.
Ex324 : Power switch was turned off, while Auto-loader was moving.
Ex325 : A plate cannot be carried to intermediate sensor.
Ex326 : A slipping paper under a plate was detected. Or a plate size (in the Y direction) is shorter than the set
value.
Ex327 : The bridge-passing sensor does not turn OFF.(for Jig mode)
Ex328 : Door is open.
Ex340 : Door is open.
Ex341 : The interlock switch-3 is OFF.
Ex342 : The interlock switch-2 is OFF.
Ex343 : The interlock switch-1 is OFF.
Ex344 : A fuse on the relay board was blown. (home)
Ex345 : A fuse on the relay board was blown. (away)
Ex346 : Nip roller does not descend.
Ex347 : Nip roller does not ascend.
Page (6)
SCREEN CONFIDENTIAL
Ex348 : Shutter does not open.
Ex349 : Shutter does not close.
Ex360 : A plate remains on the bridge's sensor-1.
Ex361 : No plate exists on the bridge's sensor-3.
Ex362 : A plate remains on the bridge's sensor-3.
Ex363 : A plate size in the Y direction is too long when its transferring to the AT.
Ex364 : A plate size in the Y direction is too short when its transferring to the AT. Or an interleaf in front of a
plate was detected.
Ex365 : After the paper pad is descended, the metal sensor does not switch to ON.
Ex366 : Plate pad dropped the plate, before this initialize.
Ex367 : A teaching of plate size in the Y direction (1st) is finished.
Ex368 : A teaching of plate size in the Y direction (2nd) is finished.
Ex369 : This plate can't be transed. Because something error has occured when the transfering to AT.
Ex36a : Air pressure in the plate pad does not go down after retry.
Ex36c : This plate is judge as a paper during judgement operation.
Ex36d : This plate can't be transed. Because trans path position is down.
Ex380 : The door of the cassette part is open.
Ex381 : Time-out error has occurred when lift was initialized.
Ex382 : Time-out error has occurred when lift was moved.
Ex383 : Though the lift was initialized, the origin sensor is not ON.
Ex384 : The lift is not in the position where it is specified.
Ex385 : Already, there has been a cassette on the lift.
Ex386 : There are some cassettes which aren't being set properly.
Ex388 : There is no cassette in the specified cassette slot.
Ex389 : There is no cassette on the lift.
Ex38a : Lift has traveled beyond the limit (on the Up side).
Ex38b : Lift has traveled beyond the limit (on the Down side).
Ex38d : A cassette is already in the place to return a cassette.
Ex38e : A lift can't be raised and lowered because some cassettes are not in the lift or the cassette properly.
Ex38f : Time-out error has occurred when a cassette was moved to cassette part.
Ex390 : Time-out error has occurred when a cassette was moved to lift.
Ex391 : Either plate pad or paper pad is not in original point.
Ex392 : An ineffective cassette number was indicated.
Ex393 : Cassette has traveled beyond the limit (on the Lift side).
Ex394 : Cassette has traveled beyond the limit (on the Cassette side).
Ex395 : MA-L can't be initialized because some cassettes can't be returned to the origin.
Ex396 : Though there is a cassette on the lift, the place to return the cassette isn't vacant.
Ex397 : Though the movement of the lift was finished, the lift position sensor at the target position is not on.
Ex398 : MA-L Servo alarm
Ex399 : Time-out error has occurred when arm was moved.
Ex39a : Time-out error has occurred when a cassette was moved to cassette part by arm.
Ex39b : Arm jut-out sensor (LS210E) is off.
Ex39c : A cassette is in illegal position of the cassette slot.
Ex39d : Arm is not in original point.
Ex39e : SQ210A sensor is illegal.
Ex3a0 : Autoloader power is OFF, or all interlock switches are OFF.
Ex3a1 : Autoloader's maintenance cover is open.
Ex3a2 : Cassette carrier not set.
Ex3a3 : Zero-point sensor for pad transport not OFF at time of zero-point return.
Ex3a4 : Zero-point sensor for pad rotation not OFF at time of zero-point return.
Ex3a5 : Zero-point sensor for pad transport (or zero-point sensor for pad rotation) not OFF at time of
zero-point return.
Ex3a6 : Pad rotation motor not at zero point at time of zero-point return by pad transport motor.
Ex3a7 : Pad transport motor cannot do zero-point return.
Ex3a8 : Pad transport zero-point sensor not ON after zero-point return by pad transport motor.
Ex3a9 : Pad rotation motor cannot do zero-point return.
Ex3aa : Pad rotation zero-point sensor not ON after zero-point return by pad rotation motor.
Ex3ab : Timeout from sensor for prohibited pad rotation position during separate operation.
Page (7)
SCREEN CONFIDENTIAL
Ex3ac : Timeout at sensor for prohibited pad rotation during transfer.
Ex3ad : Plate detected at autoloader's conveyer rollers.
Ex3af : Zero-point sensor for pad transport not going OFF.
Ex3b0 : Zero-point sensor for pad rotation not going OFF.
Ex3b1 : Timeout for carrier lock DC motor rotation.
Ex3b2 : Zero-point sensor not ON after carrier lock.
Ex3b3 : Timeout for carrier lock DC motor rotation.
Ex3b4 : Zero-point sensor not OFF after cassette lock cleared.
Ex3b5 : Timeout during position change for pad customization.
Ex3b6 : Drop in vacuum pressure at start of plate transport.
Ex3b7 : Plate dropped near carrier during plate transport.
Ex3b8 : Plate dropped during handling movement.
Ex3b9 : Plate dropped between units during plate transport.
Ex3ba : Plate dropped near conveyer rollers during plate transport.
Ex3bb : Vacuum pressure not OFF after vacuum pump turned OFF.
Ex3bc : Timeout without completing PCL status at time of pad transport motor step operation.
Ex3bd : Plate transported, but interleaf detected.
Ex3be : Pad transport motor not at zero point after plate transported to rollers.
Ex3bf : Pad rotation motor not at zero point after plate transported to rollers.
Ex3c0 : Plate transported, but interleaf adhering to plate front, or plate's [Y] size shorter than setting.
Ex3c1 : A plate cannot be carried into the transport unit.
Ex3c2 : Plate transported, but plate remains on conveyer rollers (plate's [Y] size longer than setting.)
Ex3c3 : Possible collision as pad rotation motor not returned to zero point.
Ex3c4 : Timeout without completing PCL status at time of pad transport motor movement.
Ex3c5 : Timeout without completing PCL status at time of pad rotation motor movement.
Ex3c6 : Power cut during operation.
Ex3c7 : Maintenance cover opened.
Ex3c8 : Cassette carrier out.
Ex3c9 : Plate dropped without nipping at conveyer rollers.
Ex3ca : PT-R's door open.
Ex3cb : Plate on PT-R's conveyer table prior to plate transport from SA-L.
Ex3cc : Autoloader power is OFF.
Ex400 : Plate has already been loaded.
Ex401 : Plate has not been loaded.
Ex402 : Door is open.
Ex403 : Dump papers which collected in the box.
Ex600 : Either the conveyer, processor, or stacker is not turned on, or is in the busy status or error status.
Ex601 : Either the conveyer, processor, or stacker is not turned on, or is in the busy status or error status.
Ex602 : The plate is not possible to be transfered into AT unit.
Ex603 : The plate cannot be transferred completely into the AT unit.
Ex606 : Error
Ex607 : Busy
Ex608 : Error
Ex609 : Busy
Ex60a : Error
Ex60b : Busy
Ex60c : Error occurred in ATM while a plate was carried to ATM.
Ex80c : The result of the calculation "Initial value + increment value * (repetition - 1)" exceeds the upper limit
value.
Ex80d : (The result of the calculation "Exposure starting point + (pattern width + gap) * (repetition - 1)"
exceeds the plate size.
Ex80e : The specified plate is not linked with the printing-machine's data.
Ex80f : Initialization process is not completed.please reboot.
Ex810 : No plate is set at inlet of transport unit.
Ex811 : Plate (printer) size specified by host computer is not registered.
Ex812 : Image size specified by host computer is larger than allowable output image size.
Ex813 : Current offset of printing machine settings cause image to extend off plate.
Ex814 : Current Adjust of printing machine settings cause image to extend outside of allowable exposure
Page (8)
SCREEN CONFIDENTIAL
area.
Ex815 : The exposure area cannot be secured.
Ex816 : Some LD is (are) nearing the end of life. Please contact our office or agency to replace with new
one(s).
Ex817 : There are some punch blocks which have been used more than endurance time. Please contact our
office or agency and ask to replace them.
Ex819 : It failed to read the cassette number. It considers that the cassette number is No.1.
Ex81a : Some LD cannot be calibrated to target power. Calibration has been done to lower target and usable,
but please contact our office or agency.
Ex81b : Some LD cannot be calibrated to target power. Temporary the machine is working with half channels
of LD. Please contact our office or agency.
Ex81c : Some LD cannot be calibrated to target power. Calibration must be done.
Ex81d : Temperature of environment > 28 degrees.
Ex81e : Temperature of environment < 18 degrees.
Ex81f : Sensor for temperature of environment has not been connected.
Ex820 : The maintenance time of Trail clamps is drawing near. Please contact our office or agency and
request those maintenances.
Ex821 : Trail clamps have been used for more than the endurance time. Please contact our office or agency
and request those maintenances.
Ex822 : Backup/restore of the data on NVRAM can't be performed, because the Dip-Sw 2 is not on.
Ex823 : The backup of the data on NVRAM is not in Flash-Memory.
Ex824 : LD calibration is required, as LD power deviated from target power. But it cannot be processed
because LD block temperature is too low.
Ex825 : The direction where a connected conveyer can't be changed is set up in the plate types setting.
Ex826 : No respons was returned from the conveyer.
Ex827 : An error was returned from the conveyer toward the switching command.
Ex828 : The conveyer can't be changed to the direction that is set up in the plate types setting.
Ex82a : LD calibration has been done, as LD power deviated from target power.
Ex82b : Test mail
Ex82c : No response come from DNS.
Ex82e : It failed in the connection to the signal tower via network.
Ex82f : The name of the mail server isn't right.
Ex830 : It failed in the connection to the mail server.
Ex831 : Mail account was rejected.
Ex832 : An error occurred in the transmission of DATA command.
Ex833 : An error occurred in the transmission of header.
Ex834 : An error occurred in the transmission of body.
Ex835 : An error occurred in the transmission of attached file.
Ex836 : An error occurred in the transmission of TO command.
Ex837 : A command was sent to the SMTP server. But, no answer was returned from the server.
Ex838 : An error occurred in the POP befor SMTP.
Ex839 : The head task was hanged up.
Ex83a : Execute the calibration against all the following resolutions. Cannot expose until the calibration is
done.
Ex83b : LD calibration has been done, as LD power DEVIATED MUCH from target power.
Ex83c : It is time to replace the filter in the air filtering unit. Note that, after replacing the filter, it is necessary
to press the RESET button of the counter for the Dust filter in the Consumable Timer screen.
Ex83f : Compressor linked LD have been used for more than the endurance time. Please contact our office or
agency and request those maintenances.
Ex840 : The DHCP server is started. Don't connect the engine with user's LAN.
Ex841 : Could not initialize due to the download mode.
Ex870 : Drum servo is not matched.
Ex871 : Image control board is not matched.
Ex880 : Product-Key data is not matched.
Ex881 : Brand-Code data is not matched.
Ex890 : An error occurred in SMTP AUTH process.
Ex891 : SMTP AUTH is not supported.
Ex892 : SMTP AUTH authentication failed
Page (9)
SCREEN CONFIDENTIAL
Ex8f0 : Servo pack: Time-out error occurred while receiving data.
Ex8f1 : Servo-Pack:Address error
Ex8f2 : Servo-Pack:Data error
Ex8f3 : Servo-Pack:Check sum error
Ex8f4 : Servo-Pack:Undefined error code
Ex8f5 : Servo-Pack:Number of received characters is insufficient.
Exe01 : Excessive current in the LD drive (driver 1 board)
Exe02 : Excessive current in the LD drive (driver 2 board)
Exe03 : Excessive current in the LD drive (driver 3 board)
Exe04 : Excessive current in the LD drive (driver 4 board)
Exe05 : Driver board temperature error or FPGA Version error
Exe06 : -5 V power supply error
Exe07 : Calibration sensor is not connected.
Exe08 : Offset error in the calibration sensor
Exe09 : Irregular 5 V power supply
Exe0a : Irregular +15 V power supply
Exe0b : Irregular -15 V power supply
Exe0c : Irregular 24 V power supply
Exe0d : Cover switch is OFF.
Exe0e : BL command error (counter value is 0)
Exe0f : Zoom sensor does not detect.
Exe10 : Focus sensor does not detect.
Exe11 : Time over for home return.(zoom or focus motor)
Exe12 : Power supply irregular while the motor is driving.(zoom or focus motor)
Exe13 : Pulse motor has traveled beyond the limit. (Zoom or focus motor)
Exe14 : Irregular power supply(instantaneous loss)
Exe20 : Temperature of the LD block is greater than 28•. (Temperature at the periphery of the optical unit >
35•. Temperature of environment > 28•.)
Exe21 : Temperature at the periphery of the optical unit is greater than 35•. (Temperature of environment >
28•.)
Exe22 : Temperature of the radiating fin of the Peltier element is greater than 55 •. (Temperature at the
periphery of the optical unit > 35•. Temperature of environment > 28•.)
Exe23 : Dew condensation error. (Temperature of the LD block • 22•.)
Exe24 : Sensor for LD block has not been connected.
Exe25 : Sensor for the periphery of the optical unit has not been connected.
Exe26 : Sensor for the radiating fin of the Peltier element has not been connected.
Exe27 : Sensor for the dew condensation detection sensor has not been connected.
Exe28 : Temperature of the LD block is low.
Exe30 : Power supply error occurred when the recording head received the DW command.
Exe31 : Command error occurred when the recording head received the DW command.
Exe32 : Download error occurred when the recording head received the DP command.
Exe33 : Download error occurred when the recording head received the DF command.
Exe34 : Download address error occurred.
Exe35 : Error occurred when the recording head received the BU command.
Exe36 : Error occurred when the recording head received the BD command.
Exe40 : Writing error occurred when the recording head received the AC command.
Exe41 : Writing error on EEPROM
Exe42 : RAM error
Exe43 : ROM check sum error
Exe44 : FPGA error
Exe45 : Data error due to a divide-by-zero error
Exe60 : LD current setting Error
Exe61 : Temperature of the LD block > 28•. (Temperature at the periphery of the optical unit > 35•.
Temperature of environment • 28•.)
Exe62 : Temperature of the LD block > 28•. (Temperature at the periphery of the optical unit • 35•.
Temperature of environment > 28•.)
Exe63 : Temperature of the LD block > 28•. (Temperature at the periphery of the optical unit • 35•.
Temperature of environment • 28•.)
Page (10)
SCREEN CONFIDENTIAL
Exe64 : Temperature at the periphery of the optical unit > 35•. (Temperature of environment • 28•.)
Exe65 : Temperature of the radiator > 55•. (Temperature at the periphery of the optical unit > 35•.
Temperature of environment • 28•.)
Exe66 : Temperature of the radiator > 55•. (Temperature at the periphery of the optical unit • 35•.)
Exe67 : The LD block has dew.(Temperature of the LD block < 22•. Temperature inside the machine • 18•.)
Exe68 : The LD block has dew.(Temperature of the LD block < 22•. Temperature inside the machine < 18•.)
Exe69 : Temperature of the LD block < 5•.(Temperature at the periphery of the optical unit • 17•.)
Exe6a : Temperature of the LD block < 5•.(Temperature at the periphery of the optical unit < 17•.
Temperature of environment • 18•.)
Exe6b : Temperature of the LD block > 28•.(Temperature at the periphery of the optical unit > 35•.
Temperature of environment • 28•.)
Exe6c : Temperature of the LD block > 28•.(Temperature at the periphery of the optical unit • 35•.
Temperature of environment > 28•.)
Exe6d : Temperature of the LD block > 28•.(Temperature at the periphery of the optical unit • 35•.
Temperature of environment • 28•.)
Exe6e : Temperature at the periphery of the optical unit > 35•.(Temperature of environment • 28•.)
Exe6f : Temperature of the radiator > 55•. (Temperature at the periphery of the optical unit > 35•.
Temperature of environment • 28•.)
Exe70 : Temperature of the radiator > 55•. (Temperature at the periphery of the optical unit • 35•.)
Exe71 : It is just before an exposure head has dew.(Temperature of the LD block < 22•. Temperature of
environment • 18•.)
Exe72 : It is just before an exposure head has dew.(Temperature of the LD block < 22•. Temperature of
environment < 18•.)
Exe73 : 5• • Temperature of the LD block < 17•.(Temperature of environment • 18•.)
Exe74 : 5• • Temperature of the LD block < 17•.(Temperature of environment < 18•.)
Exea0 : Light intensity adjustment error 0ch
Exea1 : Light intensity adjustment error 1ch
Exea2 : Light intensity adjustment error 2ch
Exea3 : Light intensity adjustment error 3ch
Exea4 : Light intensity adjustment error 4ch
Exea5 : Light intensity adjustment error 5ch
Exea6 : Light intensity adjustment error 6ch
Exea7 : Light intensity adjustment error 7ch
Exea8 : Light intensity adjustment error 8ch
Exea9 : Light intensity adjustment error 9ch
Exeaa : Light intensity adjustment error 10ch
Exeab : Light intensity adjustment error 11ch
Exeac : Light intensity adjustment error 12ch
Exead : Light intensity adjustment error 13ch
Exeae : Light intensity adjustment error 14ch
Exeaf : Light intensity adjustment error 15ch
Exeb0 : Light intensity adjustment error 16ch
Exeb1 : Light intensity adjustment error 17ch
Exeb2 : Light intensity adjustment error 18ch
Exeb3 : Light intensity adjustment error 19ch
Exeb4 : Light intensity adjustment error 20ch
Exeb5 : Light intensity adjustment error 21ch
Exeb6 : Light intensity adjustment error 22ch
Exeb7 : Light intensity adjustment error 23ch
Exeb8 : Light intensity adjustment error 24ch
Exeb9 : Light intensity adjustment error 25ch
Exeba : Light intensity adjustment error 26ch
Exebb : Light intensity adjustment error 27ch
Exebc : Light intensity adjustment error 28ch
Exebd : Light intensity adjustment error 29ch
Exebe : Light intensity adjustment error 30ch
Exebf : Light intensity adjustment error 31ch
Exec0 : Light intensity adjustment error 32ch
Page (11)
SCREEN CONFIDENTIAL
Exec1 : Light intensity adjustment error 33ch
Exec2 : Light intensity adjustment error 34ch
Exec3 : Light intensity adjustment error 35ch
Exec4 : Light intensity adjustment error 36ch
Exec5 : Light intensity adjustment error 37ch
Exec6 : Light intensity adjustment error 38ch
Exec7 : Light intensity adjustment error 39ch
Exec8 : Light intensity adjustment error 40ch
Exec9 : Light intensity adjustment error 41ch
Execa : Light intensity adjustment error 42ch
Execb : Light intensity adjustment error 43ch
Execc : Light intensity adjustment error 44ch
Execd : Light intensity adjustment error 45ch
Exece : Light intensity adjustment error 46ch
Execf : Light intensity adjustment error 47ch
Exed0 : Light intensity adjustment error 48ch
Exed1 : Light intensity adjustment error 49ch
Exed2 : Light intensity adjustment error 50ch
Exed3 : Light intensity adjustment error 51ch
Exed4 : Light intensity adjustment error 52ch
Exed5 : Light intensity adjustment error 53ch
Exed6 : Light intensity adjustment error 54ch
Exed7 : Light intensity adjustment error 55ch
Exed8 : Light intensity adjustment error 56ch
Exed9 : Light intensity adjustment error 57ch
Exeda : Light intensity adjustment error 58ch
Exedb : Light intensity adjustment error 59ch
Exedc : Light intensity adjustment error 60ch
Exedd : Light intensity adjustment error 61ch
Exede : Light intensity adjustment error 62ch
Exedf : Light intensity adjustment error 63ch
Exee0 : Incorrect command has been input.
Exee1 : Temperature of the LD block > 28•.(Temperature at the periphery of the optical unit > 35•.
Temperature of environment > 28•.)
Exee2 : Temperature at the periphery of the optical unit > 35•.(Temperature of environment > 28•.)
Exee3 : Temperature of the radiator > 55•. (Temperature at the periphery of the optical unit > 35•.
Temperature of environment > 28•.)
Exee4 : It is just before an exposure head has dew.(Temperature of the LD block • 22•..)
Exee5 : Temperature of the LD block < 5•.(Temperature at the periphery of the optical unit < 17•. Tem
Page (12)